Gateway  
Top SUPPORT@ Download Service Technical Information Installation Guide
Installation Guide
Operating System
Operationg System
Desktop
Desktop
Gateway PROFILE
Gateway PROFILE
Portable
SOLO 2500
SOLO 9100
SOLO 2150
SOLO 3150
SOLO 9300 (16.0x)
SOLO 9300 (16.8x)
SOLO 5300
 
Update: 2000/11/01
Installation Guide

SMC EZ Card 10/100 (1211TX)

Target
  Windows NT 4.0

To install the driver
Preparing for Installation
  SMC 1211TX Driver Disk (Floppy Disk)
Microsoft Windows NT 4.0 CD (CD-ROM)

    If you would like to see the procedure with pictures, click here .
    Procedure with pictures

  1. Start the Windows.

  2. Log on with Administrative rights.

  3. On your screen, locate and click on [Start] button.  From the Start menu, select [Settings] then click on [Control Panel].

  4. In the "Control Panel", double click on [Network] icon.  The [Network Configuration] window appears.

  5. Click on [Yes] to install Windows NT Networking.  The [Network Setup Wizard] window appears.

  6. Select [Wired to the network] and click on [Next].  The message [To have setup start searching for a Network Adapter, click Start Search button] appears.

  7. Click on [Select from list] button.  The [Select Network Adapter] window appears.

  8. Click on [Have Disk].  The [Insert Disk] window appears.

  9. Insert the Driver Disk into the Floppy Disk drive.

  10. In the text box, type A:\ and click on [OK].  The [Select OEM Option] window appears.

  11. Make sure that "SMC EZ Card 10/100 PCI (SMC1211 TX)" is highlighted and click on [OK].  The "Network Setup Wizard" window appears again

  12. Make sure that "SMC EZ Card 10/100 PCI (SMC1211 TX)" is selected, and click on [Next].

  13. Select the networking protocols that are used on your network, and click on [Next].

  14. Select the services that are needed on your network, and click on [Next].  The message "Windows NT is now ready to install networking components..." appears

  15. Click on [Next].  The [Windows NT Setup] window appears.

  16. Insert Windows NT 4.0 CD into the CD/DVD-ROM drive.

    note
    note    		If [Windows NT CD-ROM] window pops up on your Windows desktop screen, close the window by clicking [x] mark where is located at the top of the right-hand side corner of the window.

  17. In the text box, type D:\i386 and click on [Continue].  The [TCP/IP Setup] window appears.

    note
    note    		(D:) represents a letter of CD/DVD-ROM drive and vary in each system. If you do not know a letter of your CD/DVD-ROM drive, double click on [My Computer] icon. At the bottom of CD/DVD-ROM icon, there is a drive letter of CD/DVD-ROM drive like a (D:),(E:),(R:) and so on.

  18. Click on [Yes] or [No] and continue to setup the networking.

  19. Setup the IP Address, the network bindings and so on.  The message "Windows NT is now ready to start the network so that you can complete the installation of networking" appears.

  20. Click on [Next].  The massage "Select whether your computer will be participating in a workgroup or a domain..." appears.

  21. Select one and type the name of the workgroup or domain.  Then, click on [Next].  The message "Networking has been installed on this computer" appears.

  22. Click [Finish].  The [Network Settings Change] window appears.

  23. Take out the Driver Disk and Windows NT CD, and then click on [Yes] to restart your computer.

    CAUTION
    CAUTION    		After installing this driver, Windows NT Service Pack must be installed again.  Click here for the procedure of Windows NT Service Pack installation.
    Windows NT Service Pack

CAUTION
 Please see User's guide for your additional references. This Installation Guide is made for the initial hardware configuration systems we ship. some processes would be changed depending on your hardware configuration.


Copyright © 1996-2001 Gateway Japan, Inc. All rights reserved.
Back to Japanese Home